收藏本站
Si4420
Sensitive Reset Enabled, Ripple on V dd :
V dd
Reset threshold voltage
(600mV)
Reset ramp line
(100mV/ms)
1.6V
time
nRes
output
H
L
Sensitive reset disabled:
V dd
Reset threshold voltage
(600mV)
Reset ramp line
(100mV/ms)
250mV
time
nRes
output
H
L
Hardware reset
The hardware reset puts the controller and the corresponding analog circuits into their default state and loads the power-on values of the
registers. This mode can be activated by pulling the nRES input (pin 10) to logic low for at least 1us. The chip is ready for operation 1ms after
releasing (setting to logic H) the nRES pin.
Software reset
Software reset can be issued by sending the appropriate control command (described at the end of the section) to the chip. The result of the
command is the same as if power-on reset was occurred. When the nRES pin connected to the reset pin of the microcontroller, using the
software reset command may cause unexpected problems.
V dd line filtering
During the reset event (caused by power-on, fast positive spike on the supply line or software reset command) it is very important to keep
the V dd line as smooth as possible. Noise or periodic disturbing signal superimposed the supply voltage may prevent the part getting out
from reset state. To avoid this phenomenon use adequate filtering on the power supply line to keep the level of the disturbing signal below
10mV p-p in the DC – 50kHz range for 200ms from V dd ramp start.. Typical example when a switch-mode regulator is used to supply the radio,
switching noise may be present on the V dd line. Follow the manufacturer’s recommendations how to decrease the ripple of the regulator IC
and/or how to shift the switching frequency.
Related control commands
“FIFO and Reset Mode Command”
Setting bit<0> to high will change the reset mode to normal from the default sensitive.
“SW Reset Command”
Issuing FE00h command will trigger software reset. See the Wake-up Timer Command .
27
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI4420DYTR MOSFET N-CH 30V 12.5A 8-SOIC
SI4421DY-T1-GE3 MOSFET P-CH D-S 20V 8-SOIC
SI4427BDY-T1-GE3 MOSFET P-CH 30V 9.7A 8SOIC
SI4430BDY-T1-GE3 MOSFET N-CH 30V 14A 8-SOIC
SI4431BDY-T1-GE3 MOSFET P-CH 30V 5.7A 8SOIC
SI4435DDY-T1-E3 MOSFET P-CH 30V 11.4A 8SOIC
SI4435DY MOSFET P-CH 30V 8.8A 8-SOIC
SI4435DY MOSFET P-CH 30V 8A 8-SOIC
相关代理商/技术参数
SI4420-D1-FTR 功能描述:射频发射器 Transceiver EZRadio RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
SI4420DY 功能描述:MOSFET 30V 400a N-Ch MOSFET RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4420DY,518 功能描述:MOSFET TRENCH<=30 RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4420DY 制造商:Vishay Siliconix 功能描述:MOSFET N SO-8
SI4420DY-E3 功能描述:MOSFET 30V 12.5A 2.5W RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4420DYHR 制造商:International Rectifier 功能描述:Trans MOSFET N-CH 30V 12.5A 8-Pin SOIC 制造商:International Rectifier 功能描述:TRANS MOSFET N-CH 30V 12.5A 8SOIC - Rail/Tube
SI4420DYPBF 功能描述:MOSFET 30V 1 N-CH HEXFET 9mOhms 52nC RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4420DYPBF 制造商:International Rectifier 功能描述:TRANSISTOR 制造商:International Rectifier 功能描述:N CHANNEL MOSFET, 30V, 12.5A, SOIC